[AP]
"Please install OCR software before setting!","设置前请先安装OCR软件！"
"Open Application %s Error!","打开应用程序 %s 错误！"
"Insufficient memory!\nPlease close some of the application programs.","内存不足！\n请关闭其他应用程序。"
"Write file %s Error!\nPlease make sure that there is enough free space on the disk.","写入文件 %s 错误！\n请确认有足够的磁盘空间。"
"Application is already running!","应用程序已经运行！"
"Printer Error!","打印机错误！"
"Output size you select is larger than the paper size in printer setting.\nIf you want to continue, driver will shrink image size to fit the paper size.\nDo you want to continue?","您选择的输出尺寸大于打印机的纸张尺寸设定。\n如果继续，驱动程序将按纸张尺寸缩小图像尺寸。\n您要继续吗？"
"Confirm scan action","确认扫描动作"
"Scan Now","立即扫描"
"Abort","取消"
"MiraScan is about to start scanning. Please verify the scan settings in 'MiraScan 6 Button Configuration Tool'. Click 'Scan now' to scan immediately, or 'Abort' to scan later. Scanning will start automatically if no action is applied.","准备进行扫描，请检查'MiraScan 6 按钮设置工具'中的扫描设置是否符合要求；点击'立即扫描'开始扫描，或点击'取消'终止扫描。否则程序倒记时结束后自动进入下一步。"

"There is not enough free disk space.","没有足够的磁盘空间。"
"The file %s already exists.\nWould you like to replace the existing file?","%s 文件已存在。\n您要覆盖存在的文件吗？"
"%s is not found!\nPlease re-install the driver.","找不到%s！\n请重新安装驱动程序。"
"Please change new photo/film, or finish the scan job.","请更换新的照片/底片，或结束扫描。"
"Continue","继续"
"Done","结束"

[DS]
"Scanner is not found!\nPlease check if\n1. Scanner power is on\n2. Cable is firmly connected","未找到扫描仪！\n请查看，\n1.扫描仪是否开\n2.电缆是否连接良好。"
"Finding scanner...","寻找扫描仪..."
"Scanner initialization failure!\nPlease try again.","扫描仪初始化失败！\n请再试一次"
"Initializing memory...","初始化内存..."
"Initializing map table...","初始化颜色对映表......"
"Scanner is warming up...","扫描仪正在热机中..."
"Reading data %d%%","读取数据 %d%%"
"Calibrating...","校正中..."
"Measure Speed...","测定速度..."
"Stiaspi.dll is not found!\nPlease re-install the driver.","Stiaspi.dll文件找不到！\n请重新安装驱动程序。"
"MUICtrl.dll is not found!\nPlease re-install the driver.","MUICtrl.dll文件找不到！\n请重新安装驱动程序。"
"Calibration failure!\nPlease check if\n   1.The transparency frame is on the glass.\n   2.The power cable of TPO module is firmly connected.\n  3.TPO lamp cover is removed.\n","图像校正错误！\n请检查是否\n1. 透射稿辅助框已置于扫描窗口上，\n2. TPO模组的电源线是紧密连接的，\n3. TPO遮光罩被取掉。"
"Scanner module is locked!\nPlease follow the quick guide to unlock the scanner module.","扫描仪模组被锁定！\n请依照快速向导解除扫描仪模组锁定。"
"Calibration failure!\nPlease check if\n   The TPO module is firmly connected.","校正失败！\n请检查TPO模组是否已正确连接。"
"Read image data failure!\nPlease restart the scanner.","读取图像数据失败！\n请重新启动扫描仪。"
"\n\nCode","\n\n代码"
"BPS too large","BPS太大"
"BPS too small","BPS太小"
"PPS too large","PPS太大"
"PPS too small","PPS太小"
"NOS too large","NOS太大"
"NOS too small","NOS太小"
"Image size too large","图像尺寸太大"
"Image size too small","图像尺寸太小"
"Image does not exist","图像不存在"
"Memory allocate fails","内存分配失败"
"Null pointer","无效指针"
"Wrong scale ratio","错误的缩放比例"
"Out of level","超出色阶范围"
"There is no enough system resource.\nPlease close the other windows or application programs, and try again.","系统资源不足。\n请关闭其他windows程序或应用程序，再重试。"
"UICtrl initiate failure","UICtrl初始化失败"
"Please either reduce the width or lower the resolution!","请缩小宽度或降低分辨率！"
"Create process fails!","创建进程失败！"
"Do color matching failure!\nPlease check if\n   The ICM file is installed.","执行色彩匹配失败！\n请检查：\n	ICM文件是否安装？"
"Job %d of %d","%d / %d 任务"
"Progress","进度"
"Scan Job Information","扫描任务信息"
"Resolution","分辨率"
"Image Type","图像类型"
"Scan to","扫描至"
"Color","彩色"
"Gray","灰度"
"BW","黑白"
"Color 48 bits","48位元彩色"
"Gray 16 bits","16位元灰度"
"Cancel","取消"
"OK","确定"
"Select a scanner:","选择扫描仪："
"Scanner","扫描仪"
"Driver can not detect any object!","程序检测不到物件！"
"Open Application Error!","打开应用程序失败！"
"Mapping table file open error!\nPlease re-install the driver.","映射表文件打开错误！\n请重新安装驱动程序。"